OT factor stands for Observer-to-Target factor, which converts mils to meters. This number is used to calculate the distance between the target and observer. It is determined by taking the distance between the target and the observer on a map, dividing the result by 1000 to find the OT. Then, the OT factor is converted into a percent. If the OT is more than one mil, the ot factor must be multiplied by the same number of millimeters.
The OT factor is the distance between the observer’s mark and the target. In order to make a correct spotting, a shooter must divide the OT distance by three. This is called spotting. When the OT distance is greater than 3,500, the officer candidate will initiate a fire for effect to determine the OT factor. It should be done for each of the 900 meters, 3500 meters, and a third.
The OT factor is used in calculating the correction for L/R deviation. It should be the same for each distance. It should be rounded by one, so it is easy to see the OT factor of the two distances. Once you know the OT factor for a distance, you can calculate the correction. Then, write the results in the spaces provided and check your answers. Once you have the OT factor, you can calculate the L/R deviation, which is important for precision shooting.
The OT factor is the distance between the observer’s target and the corresponding L/R deviation. For example, a 100-meter bracket would be split in half at two thousand meters. Then, a second hundred-meter bracket would be split at three hundred meters. This will be the OT factor for a target with a range of three thousand and 900 meters. In addition, the OT factor will also be used to determine the accuracy of the L/R correction.
Aside from determining the OT distance, this factor is also used to calculate the correction for L/R deviation. It is also used to measure the distance between two points, which is called the target and observer. Once you know the OT factor, you can determine the L/R correction. You must write your answers in the spaces provided for this. If you do not know the OT factor, consult your instructor.
OT factor is the distance between a target and the observer. The OT factor is calculated based on the distance between the observer’s target. For example, when a gunshot is made at 3500 meters, the OT factor is equal to three mils. Using the OT factor, the officer can calculate the L/R deviation.
Table of Contents
What is military water discipline?
the responsibility of seeing to it that a unit does its job well and assists other units in achieving their goals and completing their missions. The saying “Supply discipline, water discipline” emphasises that discipline is readily applied in all sectors of military life. Training.
What does it imply when you say danger is close?
Term used in a request for fire to signal that friendly troops are near to the target in close air support, artillery, mortar, and naval gunfire support operations.
Is there a difference between extinguishing a blaze and covering it up?
Fire that reduces an adversary force’s capability to carry out its goal is known as suppressive fire in the military sciences. In the military, it’s dubbed “covering fire” when it’s employed to shield friendly forces from harm as they advance across the battlefield.
What gives it the moniker “howitzer?
”
They may be used to fire at targets on the ground, as well as those on land or in the air. Haufnice, a mediaeval Czech term for a multi-stone catapult, inspired the phrase “howitzer.”
When they fire a missile, what do the pilots say?
An acronym for “foxtrot,” NATO phonetically designates the letter F as a phonetic identification of “fire”. When a weapon is launched and an announcement is made over the radio, other pilots are notified so that they may avoid putting themselves in harm’s way.
What is the military use of grazing fire?
“Fire generally parallel to the ground when the centre of the cone of fire does not rise over one metre from the ground” is the definition of grazing fire given by NATO and the United States Department of Defense. Machine guns are often used to provide grazing fire.
Non-pilots are known as what among pilots?
This is the Naval Air Training and Operating Procedures Standardization (NATOPS) programme, which is also known as an NFO.
Impact registrations have a purpose, but what exactly is it?
Registering an impact Registering four rounds (two over and two short) along the OT line, either from the same data or from data 25 metres apart, is the goal of a registration (50 metres apart when PEr is greater than or equal to 25 meters).
In military terminology, what’s the difference between an artillery piece and a mortar?
These cannons have shorter barrels and lower powder loads because to the inclusion of “chambers” in the bores. Higher heights and a shorter range were the primary goals of their design. Using mortars, the enemy’s defences may be blasted with shells fired from a considerable height into the mortars.
Do artillery batteries have how many guns?
A battalion, on the other hand, would comprise up to 18 cannons, or three artillery batteries, each with up to 150 Marines.
Is there a military term for a “call to arms?
”
It is the observer’s responsibility to formulate the message known as a “call for fire” (CFF). The FDC may use this information to identify the best way to attack the target. As a request, not a command.
What is necessary for a dramatic impact to occur before a fire is ignited?
NATO doctrine states that a round is considered to be delivered to the target or adjusting/ranging point when the mean point of impact or burst is within the acceptable distance from the target. In a call for action, a term used to signify that the adjustment/range is acceptable and that the intended impact is to be achieved by firing
Do you know what the “OT” component is in the call for fire?
”
Distance between the observer and the object being seen (the “target”). The OT distance is the distance between the FO and the target.
Who summons artillery?
When requesting artillery support, “Adjust Fire” is the most typical term. One shot from an artillery batter determines whether the grid is proper in Adjust Fire mode. “Fire fore Effect” is provided after the spotter confirms the grid. The battery will then send out whatever the observer has assigned them to do.
